Page 2 of 5
Re: Cressi Leonardo (Error Code: -7)
Posted: Fri Nov 21, 2014 5:59 am
by JamworkS
Hello Nick,
Have you had a look into this?
Thank you and take care.
Re: Cressi Leonardo (Error Code: -7)
Posted: Fri Nov 21, 2014 6:16 am
by nick
I'm working on it, sorry for the delay. I will let you know once I have some news.
Re: Cressi Leonardo (Error Code: -7)
Posted: Fri Nov 21, 2014 4:53 pm
by TnT
Please
download the libdivecomputer test application, and run it with these options:
Code: Select all
chmod +x universal
./universal -v -l leonardo.log -m leonardo.bin -b leonardo <serialport>
Replace <serialport> with the correct serial port (e.g. /dev/tty.something). In
this topic you can find some more help.
Afterwards send
me the leonardo.log and leonardo.bin files. These files will help me diagnose the problem.
Re: Cressi Leonardo (Error Code: -7)
Posted: Sun Dec 07, 2014 10:03 pm
by JamworkS
TnT wrote:Please
download the libdivecomputer test application, and run it with these options:
Code: Select all
chmod +x universal
./universal -v -l leonardo.log -m leonardo.bin -b leonardo <serialport>
Replace <serialport> with the correct serial port (e.g. /dev/tty.something). In
this topic you can find some more help.
Afterwards send
me the leonardo.log and leonardo.bin files. These files will help me diagnose the problem.
I think I've done this already. If not, Nick please do let me know.
Cheers.
Re: Cressi Leonardo (Error Code: -7)
Posted: Mon Dec 08, 2014 11:49 pm
by taylorharris50
I have found that turning the watch on and off and trying over and over will eventually work. It took about 2 dozen times to get my Cressi to work and about a dozen tries before the wife's Cressi connected. The Cressi software has about the same success rate.
Re: Cressi Leonardo (Error Code: -7)
Posted: Wed Dec 31, 2014 3:41 pm
by nick
If someone here is relatively technical, could you drop me an email?
I've been looking in to this over the last few days and would like to try a couple of things, but as I don't have access to a device I need someone a bit technical to help out.
Re: Cressi Leonardo (Error Code: -7)
Posted: Sun Jan 04, 2015 11:16 pm
by JamworkS
nick wrote:If someone here is relatively technical, could you drop me an email?
I've been looking in to this over the last few days and would like to try a couple of things, but as I don't have access to a device I need someone a bit technical to help out.
Nick, I've just sent you an email.
If you need anything else, just let me know.
Kind regards.
Re: Cressi Leonardo (Error Code: -7)
Posted: Mon Feb 02, 2015 3:40 am
by jasalomone
Hello, new to board and MacDive. Having same issues with my Cressi Leonardo. Under System info, USB, CRESSI PC INTERFACE is present when my Leonardo's dock is plugged in. However, MAcDive shows no serial interfaces. I have repeatedly installed the Cressi and generic drivers, multiple machine restarts, and reset. Refreshing Serial list shows nothing.
Help?
Re: Cressi Leonardo (Error Code: -7)
Posted: Mon Feb 02, 2015 3:51 am
by nick
Installing multiple drivers is part of the issue. You will need to remove them all, and install only the cressi one linked from the website.
It's likely that you've got things in to a confused state.
The documentation for the official FTDI driver has instructions on how to remove it.
Re: Cressi Leonardo (Error Code: -7)
Posted: Mon Feb 02, 2015 6:08 am
by bubffm
jasalomone wrote:Hello, new to board and MacDive. Having same issues with my Cressi Leonardo. Under System info, USB, CRESSI PC INTERFACE is present when my Leonardo's dock is plugged in. However, MAcDive shows no serial interfaces. I have repeatedly installed the Cressi and generic drivers, multiple machine restarts, and reset. Refreshing Serial list shows nothing.
Help?
Are you on Yosemite? then thats another likely cause of the issue. I could not get any transfer done on my Yosemite Mac. Luckily, my wife is still running Mavericks and the import from Cressi on that machine was possible without problems.